User:Timitry/3-Way-Junctions

From OpenTTD
< User:Timitry(Difference between revisions)
Jump to: navigation, search
Line 26: Line 26:
  
 
== Advanced 3-way junction, alternative style ==
 
== Advanced 3-way junction, alternative style ==
[[Image:Advanced_3-Way_Junction_Alternative.PNG|thumb|left|An alternative version...]]
+
[[Image:Advanced_3-Way_Junction_Alternative.PNG|thumb|left|An alternative version]]
If the tracks going from the upper left to the lower north are your main tracks, and the connected tracks are not so important, you might prefer not to build bridges or tunnels on your mainline, either for optical reasons or for not disrupting the traffic on it. The picture to the left shows a possible setup in which the mainline remains untouched. The disadvantages of this setup are that the curves are rather narrow and widening them requires a lot of space, and doubling the bridges is rather difficult and space-consuming, too.
+
[[Image:Advanced_3-Way_Junction_Alternative_2.PNG|thumb|right|Yet another possibility]]
 +
 
 +
If the tracks going from the upper left to the lower north are your main tracks, and the connected tracks are not so important, you might prefer not to build bridges or tunnels on your mainline, either for optical reasons or for not disrupting the traffic on it. The two pictures show possible setups in which the mainline remains untouched. The disadvantages of those setups are that the curves are rather narrow and widening them requires a lot of space, and doubling the bridges is rather difficult and space-consuming, too.

Revision as of 08:54, 26 February 2009

Railway junctions
Tutorial: Junction basics | 3-way basics | 4-way basics
Advanced junctions:
3-way: 1-track sideline and 2-track mainline | Example 2 | Example 3
Example 2 | Example 3
Example 2 | Example 3


Contents

Introduction

This page covers a few basic 3-way junctions. Only block signals will be used here, although you can improve the junctions by using Path Signals. The junctions are optimised for the use with the realistic acceleration setting enabled. If your junctions are being used by fast and long trains, you might need to make the curves a bit wider, so that the trains won't slow down.

The very basic 3-way junction

The most simple 3-way junction

This junction is fast & easy to build, and will not cost much money. However, due to the block signals being used, only one train at a time will be able to use it. If you have only very few trains running on those tracks you won't have any problems, but as soon as the traffic density increases, your trains will start jamming in front of the junction.


A little improvement...

Improving the junction...

With this setup, you can improve the throughput of your junction quite a lot, since two trains driving on the parallel tracks going from the upper left to the lower right corner can use it simultaneously. However, if a train from the uppermost track wants to turn left, and a train coming from the lower left corner also wants to turn left, they will still block each other. Building a bridge instead of a tunnel would of course work the same, but remember that tunnels have no speed limits!


Advanced 3-way junction

Advanced 3-way junction

To improve the junction a bit further, we build a second tunnel and a bridge to ensure that tracks always split before they merge, and that they don't cross each other. The junction now works quite good and is already suited for moderate traffic. However, if two trains coming from the upper left corner are driving very close behind each other, and both want to go straight along the line, the second one will have to wait before the tunnel, since we do not have signals in tunnels. The signal distance of 2 on the regular track is temporarily increased to 5 by the tunnel.

Advanced 3-way junction with doubled briges

Advanced 3-way junction, now with doubled bridges
Bridges versus Tunnels

To prevent jams caused by the scenario described above, we can build two parallel bridges or tunnels, instead of just one. The second train can then use the second bridge/tunnel and does not have to wait in front of a red signal. The reason that now instead of tunnels bridges are being used is that the variant with bridges is two tiles shorter than the one with tunnels. The screenshot to the right shows the cause of this: You can't build two adjacent tunnels which begin or end at a different position, so both tunnels need to be 5 tiles long. With bridges this is possible, so they only need to be 4 tiles long, which saves you 2 tiles with this junction. Of course you can still use tunnels if you have the space and think that they look nicer or have very low speed limits on them.


Advanced 3-way junction, alternative style

An alternative version
Yet another possibility

If the tracks going from the upper left to the lower north are your main tracks, and the connected tracks are not so important, you might prefer not to build bridges or tunnels on your mainline, either for optical reasons or for not disrupting the traffic on it. The two pictures show possible setups in which the mainline remains untouched. The disadvantages of those setups are that the curves are rather narrow and widening them requires a lot of space, and doubling the bridges is rather difficult and space-consuming, too.

Personal tools